Evening all.
I have a DJI f550 running 250mW Immersion transmitter with Fatshark Attitude goggles and Spironet anntenna.
My problem is i have fairly crap reception, 100m or so.
Can anyone give me any pointers on ways to improve things?
Thanks.
A couple of pics of your gear might help mate
It's simple. The 3s lipo powers the transmitter directly. The Go Pro has its own battery.
The signal from the camera goes through the Naza IOSD before reaching the transmitter.
(http://img.photobucket.com/albums/v489/r32combat/Andy/D5E22D2C-7EB2-4E17-A62F-32BB2578BB3A_zpsyzwu2fwv.jpg) (http://smg.photobucket.com/user/r32combat/media/Andy/D5E22D2C-7EB2-4E17-A62F-32BB2578BB3A_zpsyzwu2fwv.jpg.html)
(http://img.photobucket.com/albums/v489/r32combat/Andy/1FF40707-9947-4FD2-B59C-030699C68E21_zpsavobrfi0.jpg) (http://smg.photobucket.com/user/r32combat/media/Andy/1FF40707-9947-4FD2-B59C-030699C68E21_zpsavobrfi0.jpg.html)
(http://img.photobucket.com/albums/v489/r32combat/Andy/302E3385-411E-407A-95C5-8E353712C563_zpsjggkrg8l.jpg) (http://smg.photobucket.com/user/r32combat/media/Andy/302E3385-411E-407A-95C5-8E353712C563_zpsjggkrg8l.jpg.html)
The setup you have is pretty standard and should work perfectly well. Although there are a number of ways to improve reception with this setup there's no point in going that route until your existing system is performing how it should, which clearly it's not.
I reckon there must be a faulty component somewhere. Apologies if I'm stating the bleedin' obvious!
It also might be something to do with the face that your antenna is mounted upside down :)
Quote from: nbpicklesno2 on September 20, 2014, 11:34:18 AM
It also might be something to do with the face that your antenna is mounted upside down :)
Nope, that a perfectly reasonable way of stopping the body of the hex from blocking the video signal.
Have you double checked your video channels ? You can be in an adjacent channel and still pick up a picture if very close - sorry if obvious, but it's worth checking everything.
Antenna up or down makes no difference - it's the radiation pattern, which is strongest off the side of the antenna, which is important. The thing to avoid is tx/rx antennae pointing at each other.
Check that all the antennae connectors both tx and and rx are clean and screwed up tight.
It could be that your vtx is not outputting the claimed power. If you can borrow an identical one off another flyer that may help to check. Be careful if it is not identical as not all vtx pinouts are the same, even if the connectors are the same.
Antenna mounted like that is the pro way of doing it, that's how I have mine. ;D
Have you ever had decent range? Is it a new set up? Have you ever had the VTx on with no antenna?
This is why it is always handy to have 2 (or 5) of everything. So you can swap things out to check for dodgy components.
Do you get a better reception if the F550 is facing in a different direction or is it 100m in any postion to you on the ground. If it's better in other directions something is blocking the antenna and don't forget the signal won't ever be any good if you fly directly overhead. I had the exact same prolem on mine and the Lipo was blocking the antenna when I flew directly in front of me.
Although it's fairly unlikely it might be worth connecting the GoPro directly to the VTX bypassing the IOSD just to eliminate one more item and it might also be an idea to move the amtenna away from the GoPro if possible.
i think the gopro is partially blocking the signal. a longer antenna (hanging further down) may give better results.
I have never had any decent range with this setup. Maybe 200m on my old plane.
If i hover at 100m and slowly rotate the craft there is no improvement in image and the image is very poor. I can hardly see anything. I have tried different channels but they are all thr same.
I have never powered up the Vtx with no antenna, but i bought it 2nd hand. Could it be that its damaged in some way?
I'll have a play tomorrow. If i get no luck am i looking at a new transmitter?
You sure the sma connectors are matching?
It is right 😀
Quote from: Lola on September 20, 2014, 10:03:38 PM
You sure the sma connectors are matching?
It is right 😀
Yes, i am sure the connectors are correct.
What about the receiving end? What setup do you have including antenna etc
Just re-read the OP - apologies. So you have a Spironet on both ends?
Quote from: tdmodels on September 20, 2014, 10:33:23 PM
Just re-read the OP - apologies. So you have a Spironet on both ends?
Yes, i have a pair of spironet antennas.
Quote from: Dragon Lady on September 20, 2014, 09:45:31 PM
I have never powered up the Vtx with no antenna, but i bought it 2nd hand. Could it be that its damaged in some way?
I'll have a play tomorrow. If i get no luck am i looking at a new transmitter?
It would certainly be useful to swap it out, I had a VTX that was fine, and then suddenly the range went and the picture dropped off like a stone (although that was more like 400m than 100m)
Have you ever powered the VTX for any amount of time with out the antenna being attached ?
Quote from: bignose13 on September 21, 2014, 06:57:21 AM
Have you ever powered the VTX for any amount of time with out the antenna being attached ?
No, I have not but being a 2nd hand unit I do not know if the previous owner did. It gets fairly warm. Not sure if that's a good sign or not.
They all get warm to the touch and need an antenna connected to prevent a burn out. You could send the vtx to Dave Brown for a check over. He is the FS service man in the UK. FYI I am getting 1800m range at 150m asl with futaba 14sg and R7008Rs rx on a clear dry day. Video is still good at that range until I turn for home. Then the motor and battery mask the signal and I just have to fly through it or climb.
This tx rx combo gives rssi downlink to the tx screen so I can see the surge and fade that triggers RTL.
EDIT
I just remembered that we had a similar problem with Attitudes earlier this year. The picture and range went right off. Turned our to be that the vrx antenna had been over tightened and cracked the pcb. Got a new one from FS and the difference was immediate. The pcb had been cracked for ages. Worth a check by getting some one to tune into your tx
Sent from my iPhone using Tapatalk
I fitted a new .6w vtx and all seems well.
Thanks for the advice guys.