thUndeadMod v3.4 - openLRS S**T just got real :)

[Cat695]

well I flashed it about 67 times...correctly

Well practice makes perfect......thanks guys for being patient

[thundead]

problem seems to be something else. I'll get to the bottom of this and release a fix by tomorrow.

[Coyote]

Cheers Mihai look forward to it :)

[thundead]

got the wrong person lol

[Coyote]

lol so I have, I keep getting you two mixed up sorry lol

[thundead]

anyway Think I found out what;s wrong with the RSSI....  the PWM is messed up because the fw uses timer1 to drove the servos... so need to find a way round this.

[thundead]

Yup, found the culprit... Will move RSSI on pin 1 and re-arrange all the ports like this:

R 1 2 3 4 5 6 7 8. bed time now though lol.

Cheers webe for pointing out this nasty bug.

Mihai Out :D

anyway Think I found out what;s wrong with the RSSI....  the PWM is messed up because the fw uses timer1 to drove the servos... so need to find a way round this.

[Coyote]

Good news then :)

[papa_lazerous]

Does this explain my RSSI being 100% and jumping down then back up? Only had this on recent FW change been driving me mental lol

[thundead]

yep, sorry mate my bad. everything got fked up when i changed the pin fron 8 (timer2) to 7 (timer1).

[papa_lazerous]

yep, sorry mate my bad. everything got fked up when i changed the pin fron 8 (timer2) to 7 (timer1).

All's well that ends well, appreciated you have sorted it so quick. I was pulling my hair out replacing wiring all weekend thinking it was my mistake lol

[thundead]

Melih's fw is always coming back to haunt me lol. I'll sort it out tomorrow anyway. sorry again.

yep, sorry mate my bad. everything got fked up when i changed the pin fron 8 (timer2) to 7 (timer1).

All's well that ends well, appreciated you have sorted it so quick. I was pulling my hair out replacing wiring all weekend thinking it was my mistake lol

[Cat695]

Its seems I'm doing something else wrong now!!

I'm flashed both TX and Rx (theundead one 3.4)......Tx green light after flash....however when I flash the Rx it goes solid red....then after that it flickers between blue and red and my servo randomly jumps for awhile then settles

when I put an input on that stick on the Tx the servo just jumps about a bit.....no smooth movement (Rx continues to flicker between blue and red, Tx stays green)

Tx powered by 2s 2200mah battery and then connected to trainer port DX6i
Rx powered from a 5v BEC to pin 1

when I disconnect Tx the Rx stops flickering

config files are the same


//####### BOOSTER #######
// 0 = No booster
// 1 = Booster
#define BOOSTER 0

//######### Band Select ##########
// 0 = 433Mhz
// 1 = 459Mhz
#define BAND 1

//######### TRANSMISSION VARIABLES ##########
#define CARRIER_FREQUENCY 459000  //  startup frequency

//####### Freq Hopping #######
// 1 = Enabled  0 = Disabled
#define FREQUENCY_HOPPING 1

//###### HOPPING CHANNELS #######
#define CHNO 6
static unsigned char hop_list[10] = {0,45,5,40,10,35,15,30,20,25};

//###### RF DEVICE ID HEADERS #######
// Change this 4 byte values for isolating your transmission, RF module accepts only data with same header
static unsigned char RF_Header[4] = {'C','a','T','T'};

//###### SERIAL PORT SPEED #######
#define SERIAL_BAUD_RATE 115200 //115.200 baud serial port speed


Any ideas??

[Cat695]

Guess what that will be my fault again......had 3.3v selected in arduino and not the 5v one

THANK YOU PAPA!!!!!

[papa_lazerous]

Guess what that will be my fault again......had 3.3v selected in arduino and not the 5v one

THANK YOU PAPA!!!!!

I made the same mistake,just ask Mihai..... :laugh: